diff --git a/board/mikrotik/crs305-1g-4s/.gitignore b/board/mikrotik/crs305-1g-4s/.gitignore
new file mode 100644
index 0000000..775b934
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/.gitignore
@@ -0,0 +1 @@
+kwbimage.cfg
diff --git a/board/mikrotik/crs305-1g-4s/MAINTAINERS b/board/mikrotik/crs305-1g-4s/MAINTAINERS
new file mode 100644
index 0000000..3823489
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/MAINTAINERS
@@ -0,0 +1,7 @@
+CRS305-1G-4S BOARD
+M:	Luka Kovacic <me@lukakovacic.xyz>
+S:	Maintained
+F:	board/mikrotik/crs305-1g-4s/
+F:	include/configs/crs305-1g-4s.h
+F:	configs/crs305-1g-4s_defconfig
+F:	arch/arm/dts/armada-xp-crs305-1g-4s.dts
diff --git a/board/mikrotik/crs305-1g-4s/Makefile b/board/mikrotik/crs305-1g-4s/Makefile
new file mode 100644
index 0000000..895331b
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2015 Stefan Roese <sr@denx.de>
+
+obj-y	:= crs305-1g-4s.o
+extra-y	:= kwbimage.cfg
+
+quiet_cmd_sed = SED     $@
+      cmd_sed = sed $(SEDFLAGS_$(@F)) $< >$(dir $<)$(@F)
+
+SEDFLAGS_kwbimage.cfg =-e "s|^BINARY.*|BINARY $(srctree)/$(@D)/binary.0 0000005b 00000068|"
+$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
+		include/config/auto.conf
+	  $(call if_changed,sed)
diff --git a/board/mikrotik/crs305-1g-4s/README b/board/mikrotik/crs305-1g-4s/README
new file mode 100644
index 0000000..f420aab
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/README
@@ -0,0 +1,23 @@
+MikroTik CRS305-1G-4S+IN
+========================
+
+CRS305-1G-4S+IN is a 4x SFP+ switch with a Gigabit Ethernet port for management.
+Specifications:
+ - Marvell Prestera 98DX3236 switch with an integrated ARMv7 CPU
+ - 512 MB DDR3 RAM
+ - UART @ 115200bps
+ - 4x SFP+
+ - Gigabit Ethernet (AR8033)
+ - 16 MB SPI flash (Winbond 25Q128JVSM)
+
+Currently supported hardware:
+ - UART boot (using kwboot) and console
+ - SPI boot, environment and load kernel
+
+Planned:
+ - Gigabit Ethernet support
+
+Getting binary.0
+================
+binary.0 (DDR3 init phase) can be retrieved/extracted from the integrated bootloader on the SPI flash.
+Then binary.0 can be replaced with the extracted blob.
diff --git a/board/mikrotik/crs305-1g-4s/binary.0 b/board/mikrotik/crs305-1g-4s/binary.0
new file mode 100644
index 0000000..8dd6872
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/binary.0
@@ -0,0 +1,11 @@
+--------
+WARNING:
+--------
+This file should contain the bin_hdr generated by the original Marvell
+U-Boot implementation. As this is currently not included in this
+U-Boot version, we have added this placeholder, so that the U-Boot
+image can be generated without errors.
+
+If you have a known to be working bin_hdr for your board, then you
+just need to replace this text file here with the binary header
+and recompile U-Boot.
diff --git a/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c b/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
new file mode 100644
index 0000000..d1d1f40
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/gpio.h>
+#include <linux/mbus.h>
+#include <linux/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * These values and defines are taken from the Marvell U-Boot version
+ * "u-boot-2013.01-2016_T1.0.eng_drop_v6"
+ */
+#define DB_DX_AC3_GPP_OUT_ENA_LOW	(~(BIT(0) | BIT(2) | BIT(3) | BIT(4) \
+					| BIT(6) | BIT(12) | BIT(13) \
+					| BIT(16) | BIT(17) | BIT(20) \
+					| BIT(29)  | BIT(30)))
+#define DB_DX_AC3_GPP_OUT_ENA_MID	(~(0))
+#define DB_DX_AC3_GPP_OUT_VAL_LOW	(BIT(0) | BIT(2) | BIT(3) | BIT(4) \
+					| BIT(6) | BIT(12) | BIT(13) \
+					| BIT(16) | BIT(17) | BIT(20) \
+					| BIT(29)  | BIT(30))
+#define DB_DX_AC3_GPP_OUT_VAL_MID	0x0
+#define DB_DX_AC3_GPP_POL_LOW		0x0
+#define DB_DX_AC3_GPP_POL_MID		0x0
+
+int board_early_init_f(void)
+{
+	/* Configure MPP */
+	writel(0x00142222, MVEBU_MPP_BASE + 0x00);
+	writel(0x11122000, MVEBU_MPP_BASE + 0x04);
+	writel(0x44444004, MVEBU_MPP_BASE + 0x08);
+	writel(0x14444444, MVEBU_MPP_BASE + 0x0c);
+	writel(0x00000001, MVEBU_MPP_BASE + 0x10);
+
+	/*
+	 * MVEBU_GPIO0_BASE is the User LED
+	 * MVEBU_GPIO1_BASE is the Reset Button (currently not used)
+	 */
+
+	/* Set GPP Out value */
+	writel(DB_DX_AC3_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+	/* writel(DB_DX_AC3_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); */
+
+	/* Set GPP Polarity */
+	writel(DB_DX_AC3_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+	/* writel(DB_DX_AC3_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); */
+
+	/* Set GPP Out Enable */
+	writel(DB_DX_AC3_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+	/* writel(DB_DX_AC3_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); */
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: " CONFIG_SYS_BOARD "\n");
+
+	return 0;
+}
diff --git a/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in b/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
new file mode 100644
index 0000000..2dbbbd0
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION		1
+
+# Boot Media configurations
+BOOT_FROM	spi
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY board/mikrotik/crs305-1g-4s/binary.0 0000005b 00000068